|
www.TK560.com Vacuum Forming, Movie Prop, Sci-fi and GIjOE Forum
|
|
|
View previous topic :: View next topic |
Author |
Message |
knightshade Expert
Joined: 19 Jun 2005 Posts: 123 Location: Rochester NY
|
Posted: Wed Oct 12, 2005 12:12 am Post subject: |
|
|
crashmann -
I noticed that you mentioned that you were making your final molds out of Hydrostone plaster. I haven't worked with it before and was curious how much that differed from Hydrocal White.
I know that Hydrocal puts out quite a bit of heat while curing. It didn't seem like enough to melt plastic - but i've never tried it. My experience to date has been using it to make negatives from molds made with oil based clays. I assume that hydro-stone also heats up - but hasn't been hot enough to warping hips?
I've read up on the "technical" specs - and it looks like hydro-stone is harder once dry - and has a shorter work time. The numbers don't really give me a good reference to understand how much more durable a mold made out of Hydrostone might be - but harder seems to be a good quality
Hydrocal White:
http://sculpt.com/catalog_98/CastingMaterials/GYPSUMS/gypsum4.htm
Code: |
1 Hr. Compressive Strength 1,000 psi 6.9 MN/m2
Dry Compressive Strength 5,000 psi 34.5 MN/m2
|
Hydro-stone:
http://sculpt.com/catalog_98/CastingMaterials/GYPSUMS/gypsum7.htm
Code: |
1 Hr. Compressive Strength 4,000 psi 27.6 MN/m2
Dry Compressive Strength 10,000 psi 69.0 MN/m
|
Any recommendations on vendors?
I did a quick search tonight... best price that I noticed was just under $40 for a 100 lbs. bag (plus shipping).
Would some type of local vendor be likely to carry it?
Hardware? Pottery? Other?
(Time to break out a phone book I suppose...) |
|
Back to top |
|
|
crashmann Guru
Joined: 27 Sep 2005 Posts: 501
|
Posted: Sun Oct 16, 2005 10:46 pm Post subject: |
|
|
Hi Knightshade,
Actually, I was looking for a vendor that sold UltraCal 30 in Maryland (UltraCal 30 is supposed to capture fine details). So I went to http://www.gypsumsolutions.com, clicked on Distributors, then clicked on MD. The only place that sold any kind of USG plaster was a construction supply company - they only carried HydroStone. I read the technical specs, and I liked the idea of it being a harder material. I tried plaster of Paris from Home Depot, and it left a chalky mess on whatever it touched, and was very brittle.
The Hydrostone does heat up as it's curing. We made a chest piece about 8" deep, and I'd say it warmed up to ~150 degrees.
In the video, you can see steam coming off the elbow buck! I haven't noticed any warping from the heat (using .060 HIPS). Really, we have more trouble with making sure the mold stays level, and not warping from the weight of the plaster. It's not enough to affect the mold, but you need to be prepared as you're pouring it out.
I bought some UltraCal 30 from New York at The Compleat Sculptor, but the shipping basically doubled the price of the plaster! Definitely try to find a local dealer.
Another important recommendation - use a scale when mixing the plaster. I bought a 50 pound digital scale from here:
http://www.americanweigh.com
You've read the technical specs, be sure to weigh the plaster, then do the math to calculate the amount of water required. With HydroStone, it's 3 parts plaster to 1 part water. As I'm sifting the plaster into the water, I always end up with a dry top - there's just not enough water! But then I use a paint mixer chucked in a drill, and after a couple of minutes there's no lumps
Be sure to avoid mixing bubbles into the plaster by keeping the impeller below the surface in your 5 gallon bucket.
Good luck!
Charlie
TI-386
Last edited by crashmann on Tue Mar 28, 2006 9:46 pm; edited 3 times in total |
|
Back to top |
|
|
knightshade Expert
Joined: 19 Jun 2005 Posts: 123 Location: Rochester NY
|
Posted: Mon Oct 17, 2005 6:49 am Post subject: |
|
|
Sounds like some great info.
I've never seen a bit like that for mixing paint. Looks like I have a new gizmo to look for. I can see that it would be much better than the fork that I'm using to mix stuff
I had found a vendor about 70 miles away (Buffalo) at that same site.
As I have an event there in two weeks - I was hoping to make a detour and pic up some hydrostone. |
|
Back to top |
|
|
peterb
Joined: 29 Nov 2005 Posts: 4 Location: South Africa
|
Posted: Mon Dec 05, 2005 1:14 am Post subject: |
|
|
To summarize, I think the formulas go something like this
You choose the total Watt output of your oven, lets say you want 2300 Watts. First thing you do is calculate how many Amps you're going to need:
W = V * A
A = W / V = 2300 / 115 = 20 amps
Now to calculate the total resistance needed to draw 20 amps from 115 volts
Rt = V / A
Rt = 115 / 20 = 5.75 ohms
That's the total resistance needed, however there are 4 elements each in parallel, so the calculate the resistance of each element, we use the formula
1/Rt = 1/R1 + 1/R2 + 1/R3 +1/R4
but since each of the 4 elements are supposed to be the same, this formula can be re-written as
1/Rt = 4 * (1/R)
or
4 * (1/R) = 1/Rt
so
4 * (1/R) = 1/5.75 = 0.1739
1/R = 0.0434
R = 23 ohms
so each element must have a resistance of 23 ohms. To calculate the end-to-end resistance, we add each of the 4 element's resistance
Re = 4 * R = 92 ohms
Now, according to www.infraredheaters.com, the 22AWG wire is in 10 coiled foot lengths with a total resistance of 360 ohms, and an outside diameter of 0.30"
1 coiled foot = 360 / 10 = 36 ohms
1 coiled inch = 36 / 12 = 3 ohms
To get 92 ohms we will need
92 / 3 = 30.66 coiled inches = 2.55 coiled feet
Which works out to be about 1/4 of the 10 coiled foot length for sale at www.infraredheaters.com
Now, for intrest sake, 22 AWG = 0.025 inch in diameter, so to calculate the number of coils in 1 coiled inch
Coils = 1 / 0.025 = 40
To calculate the length of each coil, you can take the outside diameter of the coil (0.30" from the website), subtract half the wire's diameter, and then use the formula to calculate the circumference
CenterDiameter = 0.30 - (0.025 / 2) = 0.2875
Circumference = PI * Diameter = 3.1415 * 0.2875 = 0.903
So 1 coil is 0.903 inches, therefore
1 coiled inch = 40 * 0.903 = 36.128 straight inches
so your 2.55 coiled feet is approximatly 1105.51 straight inches
you can buy 10 foot lengths from www.infraredheaters.com, so the total straight length of 10 coiled feet
10 * 12 * 36.128 = 4335.397 straight inches
if the total resistance of 10 coiled feet is 360 ohms, 1 straight inch is
360 / 4335.397 = 0.083 ohms per striaght inch
therefore our 2.55 coiled feet has a total resistance of
1105.51 * 0.083 = 91.79
which comes damn close to the 92 total ohms needed, and each segment would have to be 7.65 coiled inches long
You can use those formulas to calculate a 5 or more segment oven.
Ok, to calculate the length needed to output 2300 wats at 230 volts, it would be
2300 / 230 = 10 amps
Rt = 230 / 10 = 23 ohms
4 * (1/R) = 1/Rt = 0.0434
R = 92 ohms
Re = 92 * 4 = 368 ohms
CoiledLength = 368 / 3 = 122.66 coiled inches = 10.22 coiled feet
So for people in 230 volt countries, you'll need 4 times the length of wire, but you can run it off half the amps.
For metric people, a direct conversion from www.infraredheaters.com works out to a wire of 6.35 mm diameter with a resistance of 3.2 ohms per meter.
However, the closest wire I can find is 6mm diameter, with a resistance of 3.8 ohms per meter, which means that I would need 96.84 straight meters to get 368 ohms
Please note that these calculations are in an "ideal" world
If there are any errors, please notify me, and I'll make changes |
|
Back to top |
|
|
jegner Site Admin
Joined: 30 May 2003 Posts: 2144 Location: Texas, USA
|
Posted: Mon Dec 05, 2005 8:26 am Post subject: |
|
|
WOW! Some great math there and that sounds about right for the length f material that John H. and I used for our ovens.
Thanks for sharing! |
|
Back to top |
|
|
crashmann Guru
Joined: 27 Sep 2005 Posts: 501
|
Posted: Mon Dec 05, 2005 9:05 pm Post subject: |
|
|
As Darth Vader would say... "Impressive. Most impressive."
It looks like you went all out with the formulas just like I did, and even further! Your numbers came out very close to mine, so you are right on track. Especially the calculation for number of ohms per coiled inch. I just used a ruler, measured out 1 inch, stretched it so the coils weren't touching, and took a reading. It came out to ~3 ohms.
Once you've got your oven wired up and plugged in, please let me know how it runs based on the calculations. Initially I was disappointed with the output from my oven, and found I needed to reduce the resistance (shorten the nichrome wire) in order to get decent heat output. I chalked it up to AC power calculations being a little lower than DC power.
In the end, I just stretched the wire a little further until the 20 amp breaker popped, then backed off.
Oh, and thanks for calculating the total straight length of the nichrome. 4,335" is incredibly long! That's 361 feet! Longer than an (American) football field, and with plenty left over!
Good luck!
Charlie
TI-386 |
|
Back to top |
|
|
thebluecanary Expert
Joined: 02 Feb 2006 Posts: 123 Location: St. Louis, MO
|
Posted: Tue Feb 07, 2006 8:32 am Post subject: |
|
|
Oh this will be very helpful. I was getting ready to hunt down all the old formulas and things to do what you've already done for me. =) But you mentioned breaking it over 2 seperate breakers. Would you just basicly wire up two small seperate 'ovens' inside the one oven? Like one set of outter coils, and one set of inner coils? I was thinking of doing this (I have two outlets that actually run off 2 differnet 20 amp breakers right next to each other.) The guy who wired my house before me was on crack, but he did wire up one hell of a nice workroom. |
|
Back to top |
|
|
crashmann Guru
Joined: 27 Sep 2005 Posts: 501
|
Posted: Thu Feb 09, 2006 10:44 pm Post subject: |
|
|
You are exactly right, there will be two separate coils inside the oven. That's a great way to spread the load across two separate breakers, and get plenty of heat.
Good luck!
Charlie
TI-386 |
|
Back to top |
|
|
thebluecanary Expert
Joined: 02 Feb 2006 Posts: 123 Location: St. Louis, MO
|
Posted: Fri Feb 10, 2006 8:30 am Post subject: |
|
|
crashmann wrote: | You are exactly right, there will be two separate coils inside the oven. That's a great way to spread the load across two separate breakers, and get plenty of heat.
Good luck!
Charlie
TI-386 |
Looking over, I think breaking it at the 'C' point would be best. That gives about 2 coils of the same lenght, one for inner one for outer. I'll have to give it a try and see what I get. If it doesn't work right, well, lets just hope it does. =)
edit: so 11.5 ohms for the total of each segment to keep the 20 amps. |
|
Back to top |
|
|
crashmann Guru
Joined: 27 Sep 2005 Posts: 501
|
Posted: Fri Feb 10, 2006 10:05 pm Post subject: |
|
|
As my math teacher would always say... "Let's see your work"
Current = Voltage / Resistance
Current = 120 vac / 11.5 ohms
Current = 10.4 amps
--------------------------------------
Power = Voltage * Current
Power = 120 vac * 10.4 amps
Power = 1248 watts (per coil)
Total Power = 2 * 1248 watts = 2496 watts
Not too shabby. My oven (according to the formulas) 20.5 amps * 120 vac = 2460 watts, so you would have a little more power output. And no fear of tripping a breaker
Don't forget, you've got to plug in the shop vac somewhere, and that motor pulls a good amount of juice too! Hopefully turning on the vac doesn't cause the breaker to trip (or you could run the vac on a third circuit).
Charlie
TI-386
(Did I mention it's a good idea to keep a fire extinguisher handy? ) |
|
Back to top |
|
|
Stomper Master
Joined: 01 Oct 2005 Posts: 473 Location: Woodburn, Oregon USA
|
Posted: Sat Feb 11, 2006 7:59 pm Post subject: |
|
|
If you are curious about the BTU output, there are 3.41 BTU's per watt,
so you are putting out a total of:
2496 x 3.41 = 8,511.36 BTU's of heat. _________________ Tony Krewson
FEAR... is not my god!! |
|
Back to top |
|
|
thebluecanary Expert
Joined: 02 Feb 2006 Posts: 123 Location: St. Louis, MO
|
Posted: Mon Feb 13, 2006 8:35 am Post subject: |
|
|
crashmann wrote: | As my math teacher would always say... "Let's see your work" |
Yeah yeah, I always got marked off in school for not showing my work. But I got the right answer, why do I need to show my work? =P
I plan on running the oven from either two 20 amp breakers, and the vac from one 15 amp. But one of the 20 amps in on the other side of the room, lets say 10 - 15 feet away. I might try running the Vac from this breaker, and one of the ovens from the 15 amp ones. As long as the math is right. =)
crashmann wrote: |
(Did I mention it's a good idea to keep a fire extinguisher handy? ) |
Oh I am so going to get one for electrical fires. Lowes should have what I need. I'm going to wait till its a little warmer out, just because. |
|
Back to top |
|
|
jegner Site Admin
Joined: 30 May 2003 Posts: 2144 Location: Texas, USA
|
Posted: Mon Feb 13, 2006 8:52 am Post subject: |
|
|
Safety is important! Understanding what the oven does is important too. When I started working on my oven, it was hard to find anyone that knew much about what I was trying to do. [One reason I started this site and this board]
Just be sure to use 10 gauge wire when wiring the oven, all the way back to the switch. Then use a good heavy duty wire [I used left over 10 guage with ground wire] to the plug.
Test in short intervals. Then shut everything down, and make sure all is ok.
I never had an issue with a 20amp garage circuit, unless I tried to run the shop vac on the same circuit.
Jim |
|
Back to top |
|
|
thebluecanary Expert
Joined: 02 Feb 2006 Posts: 123 Location: St. Louis, MO
|
Posted: Mon Feb 13, 2006 9:11 am Post subject: |
|
|
jegner wrote: | I never had an issue with a 20amp garage circuit, unless I tried to run the shop vac on the same circuit. |
My lights are on the same 20amp circuit, so splitting it just seemed to be a good idea. |
|
Back to top |
|
|
crashmann Guru
Joined: 27 Sep 2005 Posts: 501
|
Posted: Mon Feb 13, 2006 11:33 pm Post subject: |
|
|
jegner wrote: | Safety is important!
...
Test in short intervals. Then shut everything down, and make sure all is ok. |
Oh, you can't imagine how nervous I was when I flipped the switch! (Thus the reason why I used a 2 x 4 to turn it on and off ) I also only ran for a few minutes, shut down, started to breathe again, then ran a little longer.
As long as you're splitting the oven and vac load across separate breakers you should be fine.
I prefer to run my oven outside so the obnoxious fumes don't build up in my house. But when the temperature drops, or it's very windy, I run the oven just inside the basement door with fans running. The fumes may not be toxic, but some of the folks I've seen at GE Polymershapes are a few beers short of a 6 pack! Good ventilation is very important!
When you flip the switch, you've got to holler out the mandatory "Fire in the hole!"
Charlie
TI-386 |
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|