View previous topic :: View next topic |
Author |
Message |
propsculptor Newbie
Joined: 24 Mar 2006 Posts: 22 Location: Southern California
|
Posted: Fri Mar 24, 2006 4:29 am Post subject: Thank You tk560!!! |
|
|
I've spoken to you before (Through Email), I'm Propsculptor on the RPF and other message boards (and New here).
I just wanted to thank you for posting the progress of your vacuumform Latch that you created:
I have a smaller Vacuumformer that I custom built based on these plans:
http://www.halloweenfear.com/vacuumformintro.html but my forming platen is a little larger so I recently built a wooden frame to hold the Plastic in and couldn't figure out a way to lock it together tightly enough, until I remembered your site.
It worked great!! So thank you Very Much for posting this on the internet and helping others like me, I really appreciate your taking the time to post a website for everyone to see. |
|
Back to top |
|
|
crashmann Guru
Joined: 27 Sep 2005 Posts: 501
|
Posted: Fri Mar 24, 2006 11:20 am Post subject: |
|
|
Oh my gosh! It's you!!!
I have been pointing folks to your vac table site for years! And I suspect that Jim's first two smaller vac tables were based on your design as well. I was really bummed out when I saw the page went away a few months ago, but I'm glad to see you're back in business!
We have a couple of folks in my garrison that plan on building an over under vac table just like yours. So thank you for sharing your information!
Charlie
TI-386 |
|
Back to top |
|
|
crashmann Guru
Joined: 27 Sep 2005 Posts: 501
|
Posted: Fri Mar 24, 2006 11:32 am Post subject: |
|
|
Ok, insert foot into mouth, and chew vigorously until desired texture is achieved...
Re-reading your post, I see that you're not actually Ralis Kahn (which is where my enthusiasm came from), but you built a vac table based on his plans.
Perhaps you've seen the bus I ride on?
Nonetheless, welcome to the boards!
Charlie
TI-shortbus-386 |
|
Back to top |
|
|
propsculptor Newbie
Joined: 24 Mar 2006 Posts: 22 Location: Southern California
|
Posted: Fri Mar 24, 2006 3:27 pm Post subject: |
|
|
No I'm not Ralis Kahn, I've spoken to him but I'm not actually him.
Thanks for the welcome:)
My name is David.
crashmann wrote: | Ok, insert foot into mouth, and chew vigorously until desired texture is achieved...
Re-reading your post, I see that you're not actually Ralis Kahn (which is where my enthusiasm came from), but you built a vac table based on his plans.
Perhaps you've seen the bus I ride on?
Nonetheless, welcome to the boards!
Charlie
TI-shortbus-386 |
|
|
Back to top |
|
|
Mattax Expert
Joined: 09 Mar 2006 Posts: 160 Location: Virginia
|
Posted: Fri Mar 24, 2006 8:37 pm Post subject: |
|
|
Yes, that website is where we gathered a lot of information on my design. I guess three years of planning is finally paying off. _________________ Mattax
TK487
Garrison Tyranus |
|
Back to top |
|
|
jegner Site Admin
Joined: 30 May 2003 Posts: 2144 Location: Texas, USA
|
Posted: Fri Mar 24, 2006 10:45 pm Post subject: |
|
|
Yes, my mark II design was loosley based on his ideas. Glad that site is still up and running. |
|
Back to top |
|
|
|