View previous topic :: View next topic |
Author |
Message |
Stomper Master
![](http://i29.photobucket.com/albums/c291/TK4063/Emoticons%20and%20Avatars/BattleRage1a.jpg)
Joined: 01 Oct 2005 Posts: 473 Location: Woodburn, Oregon USA
|
Posted: Sun Feb 21, 2010 8:03 pm Post subject: Just completed my Rotocasting machine!! |
|
|
Heya Folks,
Last SundayI got a wild hair and started on a rotocasting machine. I basically just built the thing from the ideas I got off of Youtube, with the premise of a 2'x2' inner frame and built the thing outwards from there with no set dimensions. I plugged away on it a few hours every night after work, and now have it operational one week later in "manual mode". I bought a motor for it, but it didn't have enough grunt to turn it... should have gone bigger than a 1/4-HP!! I'm thinking I'll go with a DC motor, chain drive, and a variable speed controller for a finer rotational speed control when I recoup my expenses.
Anyway here's the embedded link, click on the picture and check it out!
If that doesn't work, click on this link and it'll take you to my photobucket page so you can watch it there: http://s29.photobucket.com/albums/c291/TK4063/Videos/?action=view¤t=RotocastDemo.flv _________________ Tony Krewson
FEAR... is not my god!! |
|
Back to top |
|
![](templates/aluminoid/images/spacer.gif) |
coffeehedake Novice
![](http://home.comcast.net/~coffeehedake/images/Coffee_Avatar01.jpg)
Joined: 10 Feb 2010 Posts: 66 Location: Burlington, CT
|
Posted: Sun Feb 21, 2010 8:17 pm Post subject: Rotocasting Machine |
|
|
Excellent work! _________________
![](http://home.comcast.net/~coffeehedake/images/Coffee_Logo02.jpg) |
|
Back to top |
|
![](templates/aluminoid/images/spacer.gif) |
clonesix Novice
Joined: 19 Jan 2007 Posts: 63 Location: california
|
Posted: Sun Feb 21, 2010 10:00 pm Post subject: |
|
|
Nice work. Let us know how the new motor works for you. I am building one of these myself. |
|
Back to top |
|
![](templates/aluminoid/images/spacer.gif) |
jdougn Guru
Joined: 18 Mar 2009 Posts: 714 Location: Louisville KY area
|
Posted: Mon Feb 22, 2010 9:40 am Post subject: Change to RPMs |
|
|
Nice looking rotational caster. The motor you've got may be big enough. It needs some way to decrease the overall RPM.
What are the calculations on the RPM of the rotational caster with the current motor & pulley setup in the video? How fast does the rotational caster need to turn?
If I'm looking at the setup correctly, the rotational caster would be spinning at a crazy fast speed. It looks like a straight pulley set up with both pulleys being similar in size and the motor is probably turning at 1725+rpm.
Regardless, nice looking caster. What do intend to make with it now?
DougN _________________ DougN - Just in case you're wondering, I got my "rating" legitimately... by posting aimless drivel, useless advice, and pointless questions. |
|
Back to top |
|
![](templates/aluminoid/images/spacer.gif) |
Stomper Master
![](http://i29.photobucket.com/albums/c291/TK4063/Emoticons%20and%20Avatars/BattleRage1a.jpg)
Joined: 01 Oct 2005 Posts: 473 Location: Woodburn, Oregon USA
|
Posted: Mon Feb 22, 2010 10:08 pm Post subject: |
|
|
Thanks for all the input! I plan to make copies of a Mandolorian helmet I have been working on over the last (almost) two years.
As for the existing setup, what you don't see is the wiring and motor speed controller I stripped off of it, so NO... it wouldn't be going crazy-fast! The drive pulley is an adjustable sheave opened up as far as it will go before the belt rides on the axle part of it, with a diameter of about 1.5"-2" (can't get much smaller than that!)... the other pulley is a fixed groove and is approx 7"dia. Even with the motor on "full speed" and giving it a helping hand, it still doesn't have enough grunt to overcome the needed torque to rotate the thing. I figure that if I go with a 1-hp DC motor coupled with an A/C input-D/C ouput motor speed controller I'll be good to go, plus I'll get finer speed control that way... buy alas, its more money to invest!! _________________ Tony Krewson
FEAR... is not my god!! |
|
Back to top |
|
![](templates/aluminoid/images/spacer.gif) |
jdougn Guru
Joined: 18 Mar 2009 Posts: 714 Location: Louisville KY area
|
Posted: Tue Feb 23, 2010 9:09 am Post subject: |
|
|
Obviously, I don't know what your exact setup is with the motor and pulleys. But here's a theory of what's happening with the motor right now. At full power the motor is probably trying to turn the rotational caster at hundreds of RPMs.
At "full speed" what is the rated rpm of the motor? Is it the standard 1725 RPM at full speed or less? Also, I suspect that as the speed of the motor is lowered the horse power of the motor decreases accordingly.
Here's what I think the math might be:
2" pulley on the motor at 1725rpm = 3450
3450 / 7" pulley on caster = 492 rpm
Here's an online pulley/rpm calculator that helps with the math:
http://www.temecularodrun.com/ref/rpm_calc.asp
You can enter any 3 values and it will calculate for the fourth.
To reverse this formula, if a rotational caster were set up like the Stelter Rotational Caster that CloneSix posted it would rotate at 1rpm to 36 rpm. In your setup, the motor RPM would have to be from something like 4 rpm to maybe 126 rpm. That would be difficult for most motors to handle for very long.
hth, DougN _________________ DougN - Just in case you're wondering, I got my "rating" legitimately... by posting aimless drivel, useless advice, and pointless questions. |
|
Back to top |
|
![](templates/aluminoid/images/spacer.gif) |
jegner Site Admin
![](http://www.tk560.com/TK560avitar.gif)
Joined: 30 May 2003 Posts: 2144 Location: Texas, USA
|
Posted: Tue Feb 23, 2010 11:39 am Post subject: |
|
|
Hey Tony!
Cool! That sure looks the business! you might try a really big pully on one end to see if the motor will turn it. Does not look like a lot of force to hand-crank it.
I have a couple of questions though. How will you hold your mold on the inner frame? What sort of resin do you plan to use? Slower setting stuff than 'normal'? How do you 'cap' off your molds so that the resin won't slosh out?
This is really neat, something I should do too!
Thanks for sharing!
Jim |
|
Back to top |
|
![](templates/aluminoid/images/spacer.gif) |
stormtrooperguy Expert
![](http://501neg.com/photos/albums/userpics/10011/file.jpg)
Joined: 24 Sep 2009 Posts: 126
|
Posted: Tue Feb 23, 2010 3:56 pm Post subject: |
|
|
nice! you know, i never thought about it, but a manual rotocaster wouldn't be all that bad...
i'm thinking in terms of using it in the basement part of my shop rather than the garage... i try to keep noise to a minimum in there, but turning a hand crank would be easier than slushing, and probably would look better too!
hrm, something to think about there.
any choice youtube clips that inspired you? |
|
Back to top |
|
![](templates/aluminoid/images/spacer.gif) |
Stomper Master
![](http://i29.photobucket.com/albums/c291/TK4063/Emoticons%20and%20Avatars/BattleRage1a.jpg)
Joined: 01 Oct 2005 Posts: 473 Location: Woodburn, Oregon USA
|
Posted: Sun Feb 28, 2010 5:19 pm Post subject: |
|
|
jegner wrote: | Hey Tony!
Cool! That sure looks the business! you might try a really big pully on one end to see if the motor will turn it. Does not look like a lot of force to hand-crank it.
I have a couple of questions though. How will you hold your mold on the inner frame? What sort of resin do you plan to use? Slower setting stuff than 'normal'? How do you 'cap' off your molds so that the resin won't slosh out?
This is really neat, something I should do too!
Thanks for sharing!
Jim |
I have since installed a 26" bicycle wheel in place of the larger pulley (I know its ghetto, but it works and looks half-way OK... LOL), the motor will now turn it WITH EASE! The only problem is that to reduce the RPMs to a usable rate, the motor gets overheated and cuts out on thermal overload... so a DC motor and controller will be the order of the day I rekon...
As to how to mount the mold in the frame work this is how I do it (for now), it seems to work quite well.
To "cap" the mold, I traced out the opening profile on a piece of plywood, made a "fence" around it by wrapping duct tape around the edge, and poured silicon into it while setting on a level floor. The silicon is bonded to the plywood quite nicely, and I just cinch it down with a "ratchety strap" after the batter goes in:
![](http://i29.photobucket.com/albums/c291/TK4063/Misc%20Helmets/100_1438.jpg)
I'm thinking I'll use TASK-15 from Smooth-On, I'm still researching on resin, may even go with epoxy or polyester (fiberglass) resin... dunno yet.
Here's the very first helmet I made last night using some left over polyester resin... not the greatest results (I suspect the resin "snaps" to fast and ruins the finished texture), but I could work this helmet into a usable article if I wanted to...
![](http://i29.photobucket.com/albums/c291/TK4063/Misc%20Helmets/100_1442.jpg)
![](http://i29.photobucket.com/albums/c291/TK4063/Misc%20Helmets/100_1445-1.jpg)
Here's the VERY FIRST copy I attempted from this mold hand laying all the resin and fiberglass matting... it was just... awfull... LOL!!!
![](http://i29.photobucket.com/albums/c291/TK4063/Misc%20Helmets/Picture001.jpg)
![](http://i29.photobucket.com/albums/c291/TK4063/Misc%20Helmets/Picture003.jpg)
Here's some photos of the mother mold and inner jacket:
![](http://i29.photobucket.com/albums/c291/TK4063/Misc%20Helmets/Picture005.jpg)
![](http://i29.photobucket.com/albums/c291/TK4063/Misc%20Helmets/Picture007.jpg)
stormtrooperguy wrote: | any choice youtube clips that inspired you? |
Here's a few to look at, I loosely based mine on the yellow rig in the first two links, but elected to make my frame work from wood for speed of construction and costs...
http://www.youtube.com/watch?v=ofzg_Hjukzg
http://www.youtube.com/watch?v=ArnzK6d6ugk&feature=related
http://www.youtube.com/watch?v=uTzvMg2cel0&feature=related
http://www.youtube.com/watch?v=2JhLoYk3HGY&feature=related _________________ Tony Krewson
FEAR... is not my god!! |
|
Back to top |
|
![](templates/aluminoid/images/spacer.gif) |
jegner Site Admin
![](http://www.tk560.com/TK560avitar.gif)
Joined: 30 May 2003 Posts: 2144 Location: Texas, USA
|
Posted: Sun Feb 28, 2010 6:00 pm Post subject: |
|
|
Very cool!
Thanks Tony, for sharing. Now, I gotta try one!
LOL!
Jim |
|
Back to top |
|
![](templates/aluminoid/images/spacer.gif) |
CHRISTOPHERSIM
Joined: 03 Jun 2010 Posts: 3
|
Posted: Thu Jun 03, 2010 5:41 pm Post subject: rotoational casting |
|
|
i hastily built a roto-caster a while ago in college but haven't tested it out because i was waiting until resources became available to buy a motor and variable speed control (still haven't). I'm wondering if anyone can comment on the uniformity of the cast's wall. I'm hoping to cast platsil gel 10 silicone rubber from polytek (extremely viscous) and uniformity is a must because the product is an exterior shell going over a plastic housing. Any insght or observations would be appreciated thanks? also would a stepper motor work for slower curing plastics? |
|
Back to top |
|
![](templates/aluminoid/images/spacer.gif) |
CJanssen Expert
![](http://i168.photobucket.com/albums/u165/CLJanssen/swep1_watto.jpg)
Joined: 17 Feb 2007 Posts: 215 Location: Beaverton OR
|
Posted: Thu Jun 03, 2010 6:37 pm Post subject: |
|
|
Man I miss some great threads.....NICE work Tony. I agree with Jim, I need to make one of these myself. _________________ "What, you think your some kind of Jedi?" |
|
Back to top |
|
![](templates/aluminoid/images/spacer.gif) |
TK 109 Guru
![](http://i205.photobucket.com/albums/bb208/TKstormtrooper/smith_178.jpg)
Joined: 11 May 2007 Posts: 712 Location: Galena, Ohio
|
Posted: Mon Jun 07, 2010 9:28 am Post subject: |
|
|
Yeah, Tony. This is REALLY cool stuff! ![Cool](images/smiles/icon_cool.gif) _________________ -Alex
-------------------------------------------------------
![](http://i205.photobucket.com/albums/bb208/TKstormtrooper/evil-agent-smith-1.jpg) |
|
Back to top |
|
![](templates/aluminoid/images/spacer.gif) |
stormtrooperguy Expert
![](http://501neg.com/photos/albums/userpics/10011/file.jpg)
Joined: 24 Sep 2009 Posts: 126
|
Posted: Mon Jun 07, 2010 9:13 pm Post subject: |
|
|
well, i just bought a FCAW welder last night, so i guess i'm ready to start on my rotocaster! ![Smile](images/smiles/icon_smile.gif) |
|
Back to top |
|
![](templates/aluminoid/images/spacer.gif) |
PARATECH1 Expert
![](http://i886.photobucket.com/albums/ac70/PARATECH911/Table%20Base/wicked_11.gif)
Joined: 19 Mar 2008 Posts: 112 Location: ALABAMA
|
Posted: Thu Oct 27, 2011 8:06 pm Post subject: |
|
|
Your machine looks really cool. Your mother mold looks really nice and clean. |
|
Back to top |
|
![](templates/aluminoid/images/spacer.gif) |
|